• 液壓密封件

液壓密封件

液壓密封的任務是防止液體從缸體中洩漏。 液壓密封也需要承受高壓和極端的溫度。

GMORS為液壓缸內的常見應用提供一系列密封件。 我們開發出能夠表現出良好耐磨性的合適材料。

刮塵密封 - UA2 / UA4
ua2.jpg ua4.jpg

對稱桿/活塞密封件 - UF1 / UF2 / UF4 / UH1 / UH2
uf1.jpg uf2.jpg uf4.jpg uh1.jpg uh2.jpg

活塞密封件 - UC6
uc6.jpg

Hydraulic Seals

1 Mpa = 10 Bar, 1 Bar = 14.5 psi, 1 Mpa = 145 psi

UA2
ua2.jpg

Double Lip Rod Wiper
This seal prevents entry of dust, and protects equipment by maintaining sealing performance of the packing. It can be fitted into an integrated groove. It's a double-lip all rubber wiper seal that prevents oil scraping off.
Material : NBR/FKM
Working Temperature: -35°C~+80°C/-10°C~+150°C
Surface Speed : ≦1.0m/s

UA4
ua4.jpg

 

TPU Double Lip Rod Wiper
This seal prevents entry of dust, and protects equipment by maintaining sealing performance of the packing. It can be fitted into an integrated groove. It's a double-lip all rubber wiper seal that prevents oil scraping off.

Material : ESTER TPU
Working Temperature: -30°C~+80°C
Surface Speed : ≦1.0m/s

UC6
uc6.jpg

 

Packing for Piston
Special one ring shaped packing for both sides pressure with seal lip. With the same sealing performance as U-packing. Possible to make a piston compact. PWL-Bearings for bearings combined with back-up rings are being prepared.

Material : NBR/FKM
Working Pressure: ≦14 Mpa
Working Temperature: -35°C~+80°C/-10°C~+150°C
Surface Speed : ≦1.0m/s

UF1
uf1.jpg

Symmetrical Piston/ Rod U-Cup Seal
This can be used for both piston and rod seals, and has a small section that can be fitted into an integrated groove.

Material : NBR/FKM
Working Pressure: ≦14 Mpa
Working Temperature: -35°C~+80°C/-10°C~+150°C
Surface Speed : ≦1.0m/s

UF2
uf2.jpg

TPU Symmetrical Piston/ Rod U-Cup Seal
This can be used for both piston and rod seals. It has a large section and can be used for a wide range of operations, with excellent wear resistance and sealing ability.

Material : ESTER TPU
Working Pressure: ≦35 MPA
Working Temperature: -30°C~+80°C
Surface Speed: ≦0.8m/s

UF4
uf4.jpg

TPU Symmetrical Piston/Rod U-Cup Seal
Used for both piston and rod seals, this packing has a small section and can be fitted in an integrated groove. Improved design prevents damages caused by back pressure.

Material : ESTER TPU
Working Pressure: ≦21 Mpa
Working Temperature: -30°C~+80°C
Surface Speed: ≦0.8m/s

UH1
uh1.jpg

Symmetrical Piston/Rod U-Cup Seal
The O-Ring energized lips assure a uniform, positive lip contact plus excellent low pressure sealing. Seal depth is equal to radial width. UH1 is used to interchange an existing hydraulic packing and/or O-Rings.

Material : ESTER TPU
Working Pressure: ≦35 Mpa
Working Temperature: -30°C~+80°C
Surface Speed: ≦0.8m/s

UH2
uh2.jpg

Symmetrical Piston/ Rod U-Cup Seal
The back beveled sealing lip provides greater film breaking and increased until loading at the sealing surface. Seal depth is generally 1.5 times the cross section of radial width to insure seal stability in most rugged applications. ROD SEAL use is preferred.

Material : ESTER TPU
Working Pressure: ≦35 Mpa
Working Temperature: -30°C~+80°C
Surface Speed: ≦0.8m/s

尺寸表下載

液壓密封件尺寸表

 
材料應用一覽表